Configure GazeParser.TrackingTools¶
TrackingTools configuration file is a plain text file. This is a sample of TrackingTools configuration file.
[Controller]
IMAGE_WIDTH = 320
IMAGE_HEIGHT = 240
PREVIEW_WIDTH = 640
PREVIEW_HEIGHT = 480
VALIDATION_SHIFT = 20
SHOW_CALDISPLAY = True
NUM_SAMPLES_PER_TRGPOS = 10
CALTARGET_MOTION_DURATION = 1.0
CALTARGET_DURATION_PER_POS = 2.0
CAL_GETSAMPLE_DEALAY = 0.4
TRACKER_IP_ADDRESS = 192.168.1.1
MAX_CAL_POINTS = 18
MAX_SAMPLES_PER_TRGPOS = 50
CAMERA_SAMPLING_RATE = 100.0
Following table shows the meaning of these parameters. These parameters can be set and changed without using TrackingTools configuration file.
Parameters¶
parameter |
description |
how to set/change |
---|---|---|
IMAGE_WIDTH |
Width of the image transfered from the Recorder PC. If you set non-zero value to ROI_WIDTH in SimpleGazeTracker configuration file, this value must be equal to ROI_WIDTH. Otherwise, this value must be equal to CAMERA_WIDTH in SimpleGazeTracker configuration file. |
|
IMAGE_HEIGHT |
Height of the image transfered from the Recorder PC. If you set non-zero value to ROI_HEIGHT in SimpleGazeTracker configuration file, this value must be equal to ROI_HEIGHT. Otherwise, this value must be equal to CAMERA_HEIGHT in SimpleGazeTracker configuration file. |
|
PREVIEW_WIDTH |
Width of the preview image on the presentation PC. |
|
PREVIEW_HEIGHT |
Width of the preview image on the presentation PC. |
|
VALIDATION_SHIFT |
Shift of the target position in the Validation process. If this parameter is 10, target position in the Validation is 10 pixel distant from target position in the Calibration process. |
|
SHOW_CALDISPLAY |
If this parameter is true, preview image is shown at the presentation PC. Set this parameter false if you want to hide preview image from participant. |
(press 'a' key to toggle this parameter during calibration loop) |
NUM_SAMPLES_PER_TRGPOS |
Number of calibration samples acquired at each target position. This value must be must be integer and greater than 0. If sampling frequency of SimpleGazeTracker is 120Hz and this parameter is 10, it takes 83.3 msec (1000msec/120*10) to complete sample acquisition at each target position. New in 0.6.0 |
|
CALTARGET_MOTION_DURATION |
Duration in which target moves to a calibration position. Unit is second. This value must be greater than or equal to 0 and smaller than CALTARGET_DURATION_PER_POS. New in 0.6.0 |
|
CALTARGET_DURATION_PER_POS |
Duration in which target moves to and stays at a calibration position. Unit is second. This value must be greater than or equal to 0. New in 0.6.0 |
|
CAL_GETSAMPLE_DEALAY |
Delay of starting sample acquisition from target arrived at calibration position. Unit is second. This value must not be negative and should be smaller than CALTARGET_DURATION_PER_POS minus CALTARGET_MOTION_DURATION. New in 0.6.0 |
|
TRACKER_IP_ADDRESS |
Set default IP address of SimpleGazeTracker. New in 0.6.1 |
|
MAX_CAL_POINTS |
Max calibration points supported by SimpleGazeTracker. Appropriate value of this parameter can/should be transferred from SimpleGazeTracker at runtime. New in 0.12.0 |
|
MAX_SAMPLES_PER_TRGPOS |
Max samples per target position supported by SimpleGazeTracker. Appropriate value of this parameter can/should be transferred from SimpleGazeTracker at runtime. New in 0.12.0 |
|
CAMERA_SAMPLING_RATE |
Sampling frequency of camera unit. Actual frequency can be transferred from SimpleGazeTracker at runtime. New in 0.12.0 |
|